ACEngine, ACFlex, ACModels, ACPerformance, ACPointMass, AeroPro, AircraftPro, Airships, Atmosphere, Pilots, Wind, Demos/ACEngine, Demos/ACModels, Demos/ACPointMass, Demos/AeroPro, Demos/AircraftPro, Demos/Airships, Demos/Atmosphere,
AOverAStar - A/A* computation from mach number and ratio of specific heats.
F100 - Gas Turbine 16th-order F100 linear model: Pratt and Whitney
FAIR - Computes the gas constants for hydrocarbon/air mixtures. This model
FMixedExhaustTurbofan - Function called by FZero to solve for tauTL. Only y is used by FZero.
JetEngineAnalysis - Jet engine analysis. You can vary up to two of the
JetEngineDefinitions - Definitions of data. If no output arguments are specified it will
JetEngineEfficiency - Computes the jet engine efficiency for an engine.
JetEnginePerformance - Jet engine performance. You can vary up to two of the parameters in p.
MachFromMassFlowParameter - Mach number from mass flow parameter. You need to enter a guess for
MachFromPR - Computes Mach number from pressure ratio and gamma.
MassFlow - Computes the mass flow divided by the inlet area. The code
MassFlowParameter - Mass flow parameter.
MassFlowParameterR - Mass flow parameter with gamma, r and Mach number as inputs. An
MassInflowSupersonic - Mass inflow for a supersonic diffuser
PlotGasTurbineData - Generate plots from the Gas Turbine analysis functions.
PressureRatioFromTemp - Computes pressure ratio from temperature ratio, efficiency and gamma.
PressureTotal - Total pressure.
PropellerEfficiency - Computes propeller efficency fromMach number.
PropellerPower - Propeller power and induced velocity
PropellerPowerVsV - Power vs. velocity for a propeller
RFromCPAndGamma - Computes R from cP and gamma.
RamRecovery - Ram recovery in an inlet. This computes the loss of pressure due to
StaticPumping - Static pumping of air.
TempRatioFromMachAndGamma - Computes the total temperature ratio from Mach number and gamma.
TempRatioFromPressure - Computes Temperature ratio
TemperatureTotal - Total pressure.
Theta0 - Computes the dimensionless total temperature.
Throttle - Computes the value of the burner temperature given the throttle ratio
BldFlex - Creates the flex model interfaces.
DeltaWing - Generates a double delta wing.
Fuselage - Generates a fuselage. The fuselage centerline is along x.
Wing - Generates a Wing. The tail points in the z direction.
ACWeightEstimation - Computes aircraft weight. Any parameter can be varied except type. You must
BreguetRangeEquation - Computes the Breguet range.
ConcordeLD - Optimal lift and drag coefficients for the Concorde as a function of mach
ConcordeProperties - Returns Concorde properties. The SFC and F/delta are only valid between
LiftAndDrag - Computes lift and drag coefficients for a vehicle using simple formulas.
NewtonianLD - Newtonian lift and drag per unit dynamic pressure.
RateOfClimb - Computes the rate of climb and acceleration.
Takeoff - Computes the required roll distance and liftoff velocity.
VStall - Computes the stall velocity.
APMLinMod - Compute a linear model for a point mass aircraft at a flight condition.
AircraftPointMassCLPSim - Simulate the controlled trajectory of a point mass aircraft model.
AircraftPointMassControl - Compute the control inputs for a point mass aircraft model.
AircraftPointMassDLM - Generate a discrete time-varying linear model of a point-mass aircraft.
AircraftPointMassRHS - Compute the state derivatives of a point mass aircraft model.
AircraftPointMassSim - Simulate the trajectory x(t) of a point mass aircraft model given u(t)
HorizontalWind - Form:
WindGust - Wind gust model. Generates state space equations or spectral densities.
A10 - Provides two A10 aircraft models: conventional and tilt-wing.
AIRC - AIRC aircraft model.
CCV - CCV aircraft model.
CCVSobel - CCV aircraft model with a pitch pointing mode.
CreateMVSSetupFileEntries - Creates setup file entries for MultiVehicleSim
F18Model - Generates a state space F-18 model from a range of models.
OH6A - OH6A hover model.
STOVL - Short Takeoff Vertical Landing aircraft model.
AirshipDesignGUI - High-level airship design tool.
Airship3DLayout - Plot a 3D layout of an airship model, including hull, fins, and gondola
AirshipAeroAnalysis - Plot the airship aero coefficients across angle of attack and sideslip
AirshipBallonets - Plot a 3D airship hull, fins, gondola, and show internal ballonets
AirshipDynamics - Examine the open-loop root locus across altitude, velocity, pitch
AirshipTrimAnalysis - Compute the trim controls for an airship at a range of flight conditions
GenerateAirshipAeroMats - Compute the aerodynamic force and torque for an airship at a range of
GenerateAirshipLinMods - Generate linear models of an airship at a range of flight conditions.
GetAirshipLinMod - Obtain the linear model of an airship at a particular flight condition.
LatLon - Find the latitude and longitude of a major U.S. city.
WindLatLon - Compute horizontal wind variance with latitude and longitude.
WindLatLonAlt - Compute horizontal wind variance with latitude, longitude, and altitude.
AirshipAutopilot - Autopilot for an airship.
AirshipControlSim - Controlled airship simulation with autopilot and feedback control.
AirshipLinMod - Compute a linearized model of an airship at a given flight condition.
AirshipStatespace - Extract the long. and lat.-dir. statespace models for an airship
AirshipTrim - Compute the trim controls for an airship at a given flight condition.
Airship_KLat - The lateral-directional control laws for an airship.
Airship_KLon - The longitudinal control laws for an airship.
AirshipMDot - Estimate the precent rate of change of mass per minute across altitude
AirshipMassModel - Initialize and update the airship mass model as it changes with alt.
BuildAirshipMassModel - Generate a distributed mass model for an axisymmetric airship.
IntegrateMassProps - Integrate the mass properties of multiple components into a single body
AddedMass - Generate the added mass for various geometric shapes. At this point
AirshipCV - Compute the x-location of the center of volume of an airship hull.
AirshipCoefficients - Load the approximate aerodynamic coefficients for an airship.
AirshipDrag - Compute the approximate drag on an airship.
AirshipGeometry - Compute the main geometric properties of an airship hull.
AirshipInertiaFactors - Compute the added mass/inertia factors for an airship hull.
AirshipIntegrals - Compute the geometric integrals for a double-ellipsoid airship hull.
BalanceAirshipPayload - Determine the x-location of the payload that provides long. balance.
BuildAirshipModel - Build the aerodynamic model of an airship.
CDAirship - The moment coefficient of an airship envelope. dK is a column vector.
CLAirship - The lift coefficient of an airship envelope.
CMAirship - The moment coefficient of an airship envelope. dK is a column vector.
DrawAirship - Create a 3-D image of an airship hull.
FinFactors - Compute the hull and fin efficiency factors for an airship.
FinGeometry - Compute the fin reference area, hull projection, mean chord and width.
GondolaGeometry - Compute the surface area and center of mass of an airship gondola.
HalfEllipsoid - Compute volume, surf area, centroid and specific MOI of half-ellipsoid
ASM1 - Airship Model #1
ASM2 - Airship Model #2
ASM3 - Airship Model #2
ASM4 - Airship Model #4
SolarCellCoverage - Determine the mass available for airship structure and systems.
StructuralMass - Determine the mass available for airship structure and systems.
AirshipAero - Aerodynamic forces and moments for an airship. All terms in body frame.
AirshipInit - Initialize an aircraft data structure and state for airship simulation
AirshipPropeller - Airship propeller model.
AirshipSensor - Sensor model for airship. Outputs are
AirshipSim - Simulate an airship in flight
AirshipSimGUI - GUI for setting up airship simulations
AirMass - Computes the relative air mass to sea level and a vertical path.
AtmosphereLayers - Names th atmospheric layer for altitude h.
GeoMagLatLon - Geomagnetic latitude and longitude.
GeomagneticRigidity - Geomagnetic rigidity using a dipole model.
Pilot - Build a pilot model
WindFunction - Approximate the Horizontal Wind Model (HWM93) with analytic functions
WindModel - Combined steady-state and gust model for wind. To be used in simulation.
WindTrendsDemo - Animate the variation of wind magnitude and direction.
WindsGUI - GUI for generating wind data over a range of parameters
WindsPlot - Generate 3D plots of wind data vs. altitude, latitude, longitude, time.
F100Demo - Look at the F100 model
JetEngineAnalysisDemo - Demo JetEngineAnalysis
JetEnginePerformanceDemo - Demo JetEnginePerformance
BuildAirToAirMissile - Build a generic air-to-air missile.
AircraftTrajectoryControlSim - Script to simulate aircraft trajectory control
Gust - See the response of an F16 to a gust using a state space model.
AIRCSim - Longitudinal simulation using the AIRC aircraft model.
CCVEV - Demonstrate eigenvector assignment using a CCV Model
CCVPitchPointing - Demonstrate eigenvector assignment using an STOVL Model for transition.
L1011EV - Demonstrate eigenvector assignment using a CCV Model
L1011EVConstraints - Demonstrate eigenvector assignment using an L1011 STOVL Model.
LQLTR - Demonstrate linear quadratic regulator with loop transfer recovery.
LQOF - Demonstrate linear quadratic output feedback.
OH6ABryson - Run a linearized simulation of the OH6A.
OH6ASim - Run a linearized simulation of the OH6A.
STOVLEV - Demonstrate eigenvector assignment using an STOVL Model
STOVLLatTransitionEV - Demonstrate eigenvector assignment using an STOVL Model for transition.
STOVLLonHoverEV - Demonstrate eigenvector assignment using an STOVL Model
STOVLLonTransitionEV - Demonstrate eigenvector assignment using an STOVL Model for transition.
STOVLTransitionEV - Demonstrate eigenvector assignment using an STOVL Model for transition.
AirshipAeroDemo - Demonstrate the AirshipAero function.
AirshipControlDemo - Demonstrate feedback control of an airship.
AirshipDemo - Simulate the airship dynamic model.
AirshipLinModDemo - Compare linear and non-linear simulations of an airship.
FlyAirship - Fly an Airship.
Atmosphere - Generate plots and a latex table of atm. properties across altitude.
SVN Revision: 11981
Back to API main page